Skip to content

We know the panels Columbia was built with

(410) 453-8032
(410) 453-8032 Get an Electrician Out
Interior and exterior

Lighting Installation in Columbia, MD

Recessed layouts, fixture replacements, under-cabinet runs and exterior lighting, wired on circuits that can actually carry what you are adding.

Plan a lighting job — (410) 453-8032 All services
Recessed ceiling lights illuminating a renovated kitchen

Lighting Columbia's Rooms Properly

Lighting is the service most often treated as decoration and least often treated as electrical work, which is how a kitchen ends up with twelve new cans on a circuit that was already carrying the dining room.

Lighting installation in Columbia runs from single fixture swaps to full recessed layouts in the open-plan renovations that are common across Town Center and Kings Contrivance. The electrical question is always the same: what is the circuit carrying now, what will it carry afterwards, and does the switch leg exist. We answer those before the holes get cut, and where the answer is that the circuit is already full we will price the new circuit separately so you can see what the capacity costs.

What a Lighting Job Includes

Scope depends on the room, the ceiling and what the circuit is already carrying.

  • Recessed lighting layout

    Spacing, beam angle and placement planned against the room and its ceiling height, rather than a grid dropped on a plan. Insulation contact rating is matched to the ceiling construction.

  • New or extended circuits where the load needs them

    Adding significant lighting to an already-loaded circuit is how nuisance tripping starts. We check the existing load first.

  • Fixture replacement and relocation

    Old fixtures removed, boxes checked for rating and fill, new fixtures hung level and on a box that can carry the weight.

  • Under-cabinet and task lighting

    Hard-wired runs with the transformer or driver placed where it can be serviced, not sealed behind a cabinet back.

  • Dimmer compatibility

    LED and dimmer mismatches cause most of the flicker and buzz people blame on wiring. We specify dimmers that match the drivers.

  • Switch legs, three-way and four-way circuits

    Adding a second switch at the other end of a long room is routine, including running the traveller where none exists.

  • Exterior and landscape lighting

    Weather-rated fixtures, GFCI protection, buried runs and photocell or timer control for driveways and entries.

  • Smart switch and control installation

    Where a neutral is present at the box, smart switches go in cleanly. Where it is not, we will tell you before you buy them.

  • Closet, attic and garage lighting to code

    Clearance rules in closets and fixture types in attics are both specified for a reason and both regularly ignored.

  • Clean-up and patching coordination

    Cut lines agreed in advance and the mess taken with us.

Plan the Light, Then the Circuit

01

Walk the rooms

We look at what you want lit, how the room is used and at what times of day, and what is already on the circuit. For recessed work we lay out the positions on the ceiling with you before anything is cut, because moving a can afterwards is a drywall job.

02

The written scope

Fixture count, type, circuit work, switching and dimmer specification, all itemised. If new circuits are needed, that is priced separately so you can see what the lighting costs and what the capacity costs.

03

Install and commission

Most single-room recessed jobs are a day. We cut, run, hang, terminate and test every fixture and dimmer through its full range before we leave, so flicker gets caught on our time rather than yours.

Why Columbia Homeowners Use Us for Lighting

The circuit gets checked before the fixtures get added

This is the step that separates a lighting job that works from one that trips every winter evening.

Dimmer and driver matching is part of the scope

Flicker and hum are nearly always a compatibility problem, and it is cheaper to specify correctly than to replace afterwards.

Layout is agreed before anything is cut

You approve the positions on the ceiling, in the room, with the furniture where it actually sits.

On every job of this kind

  • Licensed electricians
  • Circuit load checked before adding fixtures
  • Written scope
  • Workmanship warranty in writing

Light the Room the Way You Use It

(410) 453-8032

Tell us the room and what it is for. We will tell you roughly how many fixtures it wants and whether the existing circuit can take them. If a kitchen renovation is driving it, bring us in before the drywall closes.

Lay out your lighting — (410) 453-8032 See all services

Licensed electricians. Written scope before work starts.